Whirlpool Dryer Blower Wheel Replacement

WhirlpoolWhirlpool DryerDifficult⏱ 2 - 3 hours

Инструкция на английском (оригинал iFixit). Непонятные термины — в разделе «Основы → Словарь».

Use this guide to replace the blower wheel on your Whirlpool dryer. The blower wheel is a critical component that pulls the heated air through your dryer as it spins. It can be damaged by small pieces of laundry like socks or gloves that lodge in it and cause jams or breaks. This guide will work for most Whirlpool dryers. This guide is written with a model WED87HED dryer. If you have a different model, you may encounter some minor disassembly differences, but the overall repair process will be the same.

Сначала выполнить:Do these first:

Whirlpool Dryer Power Cord Replacement

🧰 Tools

Phillips #2 Screwdriver
5/16" Nut Driver
6-in-1 Screwdriver
5/16" Socket
Socket Wrench
1/4" Nut Driver
FixMat
3/16 Flat Head Screwdriver
1/2 inch drive socket wrench
1/2 inch drive 5" extension
Adjustable Wrench
Spudger

ШагиSteps

Safety Precautions

Before you begin your repair, unplug your dryer.
Your power cord may have four prongs rather than three. The additional prong is a ground connection.

Unfasten the top panel

Throughout this guide, keep track of each screw and reinstall it exactly where it came from.
Use a nut driver to remove the screws securing the top panel to the rear panel bracket.

Remove the top panel

Grasp the top and slide it 1/2 to 1 inch toward the rear of the machine.

Step 4

Lift the top panel upward to separate it from the chassis.
Remove the top panel from the machine.

Disconnect the control panel

Disconnect the control panel cable from the main board.

Step 6

Disconnect the drum light connector.

Unfasten the control panel

Remove the screws securing the control panel.

Remove the control panel

Lift the control panel up and tilt it away from the chassis to remove it.
Make sure to thread the cable through the hole in the chassis.
During reassembly, thread the cable through its proper hole before reinstalling the control panel.

Disconnect the door switch

Use a small flat blade screwdriver or a spudger to unlatch both sides of the door switch connector.
Unplug the connector.

Unfasten the front panel

Remove the upper front panel sheet metal screws.
Tilt the machine backwards and prop it securely, or have a friend hold it.
Remove the sheet metal screws on the bottom edge of the panel.

Step 11

Remove the screws inside the door area below the drum opening.

Remove the front panel

The panel is heavy and awkward. You may want to have a friend help you with this step.
Pull the bottom of the panel away from the chassis about two to three inches.
Lift the front panel off the small tabs on the chassis near the top of the panel and remove it.
Make sure you don't snag the door switch wire harness as you remove the panel.

Unfasten the cover plate

Remove the cover plate screw.

Remove the cover plate

Remove the cover plate.

Disconnect the cord

Remove the screws securing the cord cables.
Mark the cables with a permanent marker if needed and take a picture or draw a diagram.

Remove the cord

Pull the cord carefully down through the round hole.
Make sure you replace the connections correctly when you reassemble.

Unfasten the cord terminal block

Remove the green ground screw.
Remove the cord terminal block screws.

Move the cord terminal block

Move the cord terminal block behind the rear panel.

Unfasten the rear panel

Remove the rear panel screws.
Throughout this guide, keep track of each screw and reinstall it exactly where it came from.

Step 20

Remove the screw holding the main board bracket to the chassis.
Remove the screws from the top rear of the machine.

Remove the rear panel

Put on gloves before continuing, as the rear panel is sharp.
Lift the panel about 1/2 inch and tilt it to the rear to release it from the vent pipe.
Slide the panel off the vent pipe and remove it.

Reassembly information

During reassembly, perform the following:
Make sure that the vent pipe is fitted into the collar on the panel.
Make sure the tabs at the bottom are aligned to the bottom rim of the chassis.
Position the panel so its screw holes match with the chassis.

Remove the lint filter

Pull the lint filter up out of the lint filter slot to remove it.
These photos show the front panel in place, but the procedure is the same if the front panel is already removed.

Unfasten the lint filter housing

Remove the mounting screws securing the lint filter housing.

Remove the lint filter housing

Pull the filter housing outward from the chassis and down to remove it.

Unfasten the blower cover

The blower cover is the round plate that serves as the inlet to the blower.
Unfasten the blower cover screw.

Remove the blower cover

Lift the blower cover slightly and slide it to free the tabs which hold it in place.
Remove the blower cover.
The photos show the lower front bulkhead in place. The bulkhead doesn't affect the blower cover removal and reassembly.

Secure the blower wheel

Move to the rear of the machine to access the drive shaft.
Hold the drive shaft with an adjustable wrench on the hex portion of the drum drive pulley.
The threads on the blower wheel are left-hand threads. The wrench must be installed to the left of the pulley to keep it from rotating counterclockwise.

Remove the blower wheel

Use a socket wrench with an extension bar and no socket to fit into the square hole on the blower wheel.
Turn the wheel clockwise (to the right) to free it enough to remove it by hand.

Step 30

Rotate the blower wheel clockwise by hand until it's free from the motor shaft.
Remove the wheel from the blower housing.

To reassemble your device, follow these instructions in reverse order. Repair didn’t go as planned? Ask our Answers community for help.

«Whirlpool Dryer Blower Wheel Replacement» — автор Bill Gilbert, iFixit, лицензия CC BY-NC-SA 3.0. Показано без изменений. Открыть оригинал и комментарии →