How to Troubleshoot Flashing Lights in a Hotpoint Dryer

HotpointHotpoint DryerModerate⏱ 30 minutes - 1 hour

Инструкция на английском (оригинал iFixit). Непонятные термины — в разделе «Основы → Словарь».

Use this guide to maintain a Hotpoint Aquarius Tumble Dryer, including the TCHL73 and similar Indesit condenser dryer models. Emptying the water container, cleaning the lint filter or fluff filter, and cleaning the condenser unit can clear flashing light warnings, prevent the dryer from stopping mid-cycle, and help it run efficiently. This guide was written around the Hotpoint Aquarius TCHL73, so other models may have small layout differences.

🧰 Tools

Wet Dry Vacuum
Scrubbing Sponge
Shop Towels or Rags
Plastic Scraper
Knife

ШагиSteps

Power off the dryer

Switch the dryer off at the power supply and unplug it from the wall outlet.
Let the dryer cool before handling the filter area or condenser compartment.
Keep the dryer unplugged until the condenser unit and filter are fully reinstalled.

Empty the water container

Pull the water container out from the top-left corner of the dryer.
Carry the container to a sink and empty out all the water.
Tip the container toward the small corner hole to drain the last drops.
A completely full water container can stop the dryer from working.
Slide the empty container back into place without forcing it.

Remove the lint filter

Push the dryer door to pop it open.
Lift the lint filter out of the door opening.
Use a finger to scrape the lint and fluff off the filter in a sheet.
Put the collected lint straight into a bin.
Clean this filter after every drying cycle because it clogs quickly.

Clean and dry the filter

Use a wet/dry vacuum to remove the smaller lint pieces from the filter.
A handheld wet/dry vacuum makes it easier to reach the nooks and crannies.
Avoid pressing hard on the gauze because it can rip.
Rinse the filter under cold water for a final clean.
Don't put the filter in a dishwasher because the water is too hot.
Dry the filter completely before reinstalling it.

Clean the filter slot

Use a wet/dry vacuum to remove dust, dirt, and fibers from the slot where the filter sits.
A handheld wet/dry vacuum works well in this tight area.
Reinstall the clean filter the right way round.
The filter should slide in easily.

Remove the condenser unit

Pull the lower front flap open and fold it down.
Release the three clips holding the condenser unit in place.
Slide the condenser unit straight out toward you.
Keep a sponge or old rag ready because water may spill from the compartment.

Clean the condenser compartment

Use a cloth to wipe dust and dirt from inside the condenser compartment.
Use a wet/dry vacuum only if the compartment is dry.
Remove as much dust and fiber buildup as possible from the compartment.

Remove dry debris from the condenser

Scrape out as much lint and fiber as possible before washing the condenser unit.
Removing loose debris first helps keep it from going down the drain.
Turn the condenser over and clean the debris from the back as well.
Use a handheld wet/dry vacuum or a wet and dry vac to remove loose dirt.
Use an knife or small scraper carefully if debris is hard to reach.
Work gently so you don't cut yourself or damage the condenser fins.
Clean the condenser unit at least once a month, depending on dryer use.

Rinse and dry the condenser

Take the condenser unit to a sink, shower, or bath with a shower hose if possible.
Set the shower head to its strongest spray and run water through the condenser.
Keep the drain stopper in place while rinsing so you can remove debris before it enters the drain.
Shake excess water out of the condenser.
Let the condenser air dry for a while, or dry it as much as possible with a tea towel.
Clean debris from the bath or sink water before removing the drain stopper.

Reinstall the condenser unit

Hold the condenser at a slight angle and align it with the arrows facing the correct way up.
Slide the condenser into the compartment until it seats fully.
Don't force the condenser if it doesn't slide in easily.
Lock the condenser in place with the three clips.
Close the lower front panel.

Test the dryer

Plug the dryer back in and switch it on at the power supply.
Place damp clothes in the drum and start a drying cycle.
The empty water, clean filter, and clean condenser lights may stay on briefly until the cycle starts and the sensors activate.
Stop using the dryer if the flashing lights continue after maintenance and the container, filter, and condenser are correctly installed.

Keep up regular maintenance

Clean the lint filter every time you use the dryer.
Empty the water container regularly so it doesn't fill completely and stop the dryer.
Clean the condenser unit at least once a month, or more often if the dryer gets heavy use.
Remove all clothes after the cycle and spin the drum by hand to check for small items like handkerchiefs.
Never run the dryer with the filter or condenser unit removed.

Regularly emptying the water container, cleaning the lint filter, and cleaning the condenser unit helps prevent flashing light warnings and keeps the dryer running efficiently. Repair didn't go as planned? Ask our Answers community for help.

«How to Troubleshoot Flashing Lights in a Hotpoint Dryer» — автор eCuration, iFixit, лицензия CC BY-NC-SA 3.0. Показано без изменений. Открыть оригинал и комментарии →