GE Front Load Washing Machine Dispenser Assembly Replacement

GEGE Washing MachineModerate⏱ 2 - 3 hours

Инструкция на английском (оригинал iFixit). Непонятные термины — в разделе «Основы → Словарь».

A leaking dispenser can drip detergent, water, and rust-inducing residue across the front of your GE front-load washer. When thorough cleaning does not solve the problem, exchanging the entire dispenser assembly restores proper flow and prevents further cabinet damage. Use this procedure to remove the original box, transfer the reed switch, and install a replacement unit.

🧰 Tools

Phillips #2 Screwdriver
6-in-1 Screwdriver
Door Boot Spring Tool
Slip Joint Pliers
Pick Set

⚙️ Parts

GE Manual Dispense Drawer for Washer - WH42X35099
GE Washer Dispenser Drawer - WH42X29542
Tub dispenser hose

ШагиSteps

Remove the dispenser drawer

Pull the dispenser drawer forward until it stops.
Press firmly on the tab at the rear of the drawer and slide the drawer completely out of the housing.

Remove the screws behind the dispenser

Use a Phillips screwdriver to extract the five screws now exposed in the dispenser opening.
Keep the coarse-thread middle screws separate from the fine-thread top and bottom screws.

Free the interface panel

Lift the left side of the interface about twenty degrees then pivot it to the right and pull it away from the washer.
Do not yank; the panel is still tethered by a short wire harness.

Free harness clips for extra slack

Press the three harness clips from the inside out if you need more room to maneuver the interface.

Move the water valves if needed

Unscrew the water valve assembly and pivot it upward to gain clear access to the dispenser body.
This procedure is easier on GFW-550 models than on GFW-650 and larger machines.

Disconnect upper hoses and wiring

Unhook the wire harness from the dispenser body.
Release the top hoses that run between the water valves and the dispenser ports.
Slide the dispenser toward the rear to unlatch its right side from the chassis.

Disconnect the rear hoses

Loosen the clamps and pull off the four or five hoses attached to the back of the dispenser box.
If a hose is stuck, slip a flat screwdriver between the rubber hose and the plastic barb to break it free.

Remove the front panel

Remove the three screws underneath the washer to release the lower edge of the front panel.
Extract the seven screws securing the panel to the bulkhead.
Unscrew the two screws holding the door-lock facade and the single screw securing the lock.
Lift the lock upward and push it rearward so it will not snag the panel.

Separate the front panel

Open the washer door, lift the panel upward, and pivot it away from the machine.
Disconnect the wire harness on the left side before fully removing the panel.

Detach the large front hoses

Remove the spring clamp and pull the primary tub hose off the dispenser spigot.
Disconnect the drain hose at the underside rear of the dispenser.
Release the small hose behind the metal plate next to the dispenser box.

Remove the dispenser box

With all eight hoses free, slide the dispenser box out of the cabinet.
Inspect or clean the box now, or set it aside if you are installing a new unit.

Transfer the reed switch if required

Unclip the reed switch from the underside of the old dispenser and install it in the same location on the replacement box.

Position the new dispenser

Feed the rear drain hose onto the dispenser first before the box is fully seated.
Slide the dispenser into the front bulkhead opening and hold it in place.

Reconnect the hoses

Attach the remaining seven hoses one by one, securing each clamp firmly.
Work patiently; reinstalling the hoses usually goes faster than removal.

Route wiring and latch the dispenser

Route the harnesses into the molded channels on the dispenser body.
Slide the dispenser rearward until its rear hooks click into the washer chassis.

Attach front hoses to bulkhead

Reconnect the large front hose, aligning the molded notch with the dispenser groove.
Confirm the small alignment finger rests on the bulkhead to guide the dispenser box.

Reinstall the front panel

Lift the door panel onto its four locator pegs and push it flush with the cabinet.
Reconnect the left-side harness, then replace the upper and lower mounting screws.

Secure the damper and gasket

Ensure the top damper is fully seated, then install its three mounting screws.
Roll the door gasket lip over the rim and wear gloves to avoid cuts.

Install the gasket spring

Expand the spring with a door gasket spring tool and guide the wire around the gasket groove.
Use a small hook or screwdriver to press the wire fully home before releasing the tool.

Refit the door lock and facade

Position the door lock on its bracket and secure it with its screw.
Reattach the plastic facade using its two screws.

Reinstall the interface panel

Hook the interface onto the right-side post, pivot it down, and snap it into place.
Install the two coarse-thread center screws and the three fine-thread outer screws while holding the dispenser box flush.

Reinstall the dispenser drawer

Slide the dispenser drawer back onto its rails until it clicks fully home.

Reinstall the top panel

Lower the top panel onto the chassis and secure it with its rear screws.

Repair didn't go as planned? Ask our Answers community for help.

«GE Front Load Washing Machine Dispenser Assembly Replacement» — автор Ben Schlichter, iFixit, лицензия CC BY-NC-SA 3.0. Показано без изменений. Открыть оригинал и комментарии →