Whirlpool WED87HED Dryer Door Switch Testing and Replacement

WhirlpoolWhirlpool WED87HEDModerate⏱ 2 hours

Инструкция на английском (оригинал iFixit). Непонятные термины — в разделе «Основы → Словарь».

Use this guide to replace the door switch on your Whirlpool Duet Model WED87HED dryer. It includes steps to test the switch as well. The door switch makes sure your dryer motor won't start turning the drum if the door is open and stops it if the door is opened in the middle of a cycle. When your dryer won't start, the door switch can be the cause.

🧰 Tools

6-in-1 Screwdriver
FixMat
3/16 Flat Head Screwdriver
5/16" Nut Driver
5/16" Socket
Socket Wrench
1/4" Nut Driver
Slip Joint Pliers
Digital Multimeter

⚙️ Parts

Whirlpool Door Switch - WPW10350906

ШагиSteps

Safety Precautions

Before you begin your repair, unplug your dryer.
Your power cord may have four prongs rather than three. The additional prong is a ground connection.

Unfasten the top panel

Throughout this guide, keep track of each screw and reinstall it exactly where it came from.
Use a 5/16 inch nut driver to remove the two 15.7 mm-long screws securing the top panel to the rear panel bracket.

Remove the top panel

Grasp the top and slide it 1/2 to 1 inch toward the rear of the machine.

Step 4

Lift the top panel upward to separate it from the chassis.
Remove the top panel from the machine.

Disconnect the control panel

Disconnect the control panel cable from the main board.

Step 6

Disconnect the drum light connector.

Unfasten the control panel

Use a 1/4 inch nut driver to remove the two 16.3 mm‑long sheet metal screws located at each end of the control panel.

Remove the control panel

Lift the control panel up and tilt it away from the chassis to remove it.
Make sure to thread the cable through the hole in the chassis.
During reassembly, thread the cable through its proper hole before reinstalling the control panel.

Disconnect the door switch

Use a small flat blade screwdriver or a spudger to unlatch both sides of the door switch connector.
Unplug the connector.

Unfasten the front panel

Use a 1/4 inch nut driver to remove the three upper front panel 16.4 mm-long sheet metal screws.
Tilt the machine backwards and prop it securely, or have a friend hold it.
Use a 1/4 inch nut driver to remove the four sheet metal screws on the bottom edge of the panel:
Two 16.4 mm screws
Two 13 mm screws

Step 11

Use a Phillips driver to remove the two 15.8 mm‑long screws inside the door area below the drum opening.

Remove the front panel

The panel is heavy and awkward. You may want to have a friend help you with this step.
Pull the bottom of the panel away from the chassis about two to three inches.
Lift the front panel off the small tabs on the chassis near the top of the panel and remove it.
Make sure you don't snag the door switch wire harness as you remove the panel.

Release the door switch harness

Use slip joint pliers to pinch the tabs of the harness clip.
Push the clip through the mounting hole to release the door switch harness.

Remove the door switch

Working from the rear of the front panel, pinch the tabs on the end of the switch toward the switch body to release it.
The tabs are kind of quirky. They need to be pushed in a diagonal direction to release them. When they do release, you will know it.
Push the switch through the mounting hole toward the front of the panel.

Step 15

Feed the harness through the mounting hole to remove the switch.
The second photo shows the switch removed so you can see the mounting flange. This flange is on the front of the switch and faces the dryer door.

Test the switch

This step shows how to test the switch, which will require a multimeter. If you aren't familiar with how to use one, here is a guide that will help you.
Insert the multimeter's probes into the two outermost sockets on the switch connector and test continuity and open on the door switch.
When the button on the switch is not pushed, the meter should indicate OL.
When the button is pushed with the probes in the same place, the meter should read less than 1 Ω.
If either of these readings is wrong, especially with the button pressed, replace the switch.

To reassemble your device, follow these instructions in reverse order. Repair didn’t go as planned? Ask our Answers community for help.

«Whirlpool WED87HED Dryer Door Switch Testing and Replacement» — автор Bill Gilbert, iFixit, лицензия CC BY-NC-SA 3.0. Показано без изменений. Открыть оригинал и комментарии →