LG Front Load Washing Machine Drain Hose Replacement
LGLG Front Load Washing MachineModerate⏱ 30 - 45 minutes
Инструкция на английском (оригинал iFixit). Непонятные термины — в разделе «Основы → Словарь».
Use this guide to remove and replace the drain hose in your LG front load washing machine.
The drain hose channels wastewater out of the washer. It's a single piece of hose that's connected to the drain pump inside the washer. To replace it, you'll have to access the washer internals.
This guide will work for most LG front load washing machines. This guide is written with a model WM3050CW washer. If you have a different model, you may encounter some minor disassembly differences, but the overall repair process will be the same.
The metal ring holding the rubber boot can be difficult to reinstall. You can buy this tool to make the reinstallation easier, or ask additional people to help.
Сначала выполнить:Do these first:
🧰 Tools
- Phillips #2 Screwdriver
- Flathead 4 mm Screwdriver
- Needle Nose Pliers
- 7 mm Nutdriver
⚙️ Parts
- LG Drain Hose Assembly - AEM74772903
- LG Washer Drain Hose Assembly - 5214FR3188G
- LG Washer Drain Hose Assembly - AEM73732901
- LG Washer Drain Hose Assembly - 5215ER2002G
ШагиSteps
1
Step 1
- Turn off the main water supply
- Unplug your washer
- Disconnect all water connections at the rear of your washer
2
Unfasten the top panel
- Remove the screw(s) securing the top panel brackets to the back panel.
3
Remove the top panel
- Slide the top panel towards the rear of the device to disconnect its clips.
4
Step 4
- Tilt the top panel upward to completely disconnect it from the chassis.
- Remove the top panel.
5
Remove the detergent drawer
- Pull the detergent drawer away from the chassis as far as it will go.
6
Step 6
- Press down on the "Push" button to disengage the clips securing the detergent drawer.
- Pull the drawer out of its slot on the chassis and remove it.
7
Disconnect the control panel
- Disconnect the connectors attached to the control panel.
8
Unfasten the control panel
- Remove the screw(s) securing the control panel to the top edge of the chassis.
9
Unfasten the detergent dispenser
- Remove the screw(s) securing the detergent dispenser.
10
Unclip the control panel
- Use a flathead screwdriver, or a pry tool, to unclip the control panel from the chassis.
11
Remove the control panel
- Remove the control panel, making sure to thread any cables through the chassis.
12
Open the door
- Open the front door completely.
13
Remove the boot ring
- Use needle nose pliers to grip the spring end of the metal ring at the bottom of the rubber boot.
- Pull the ring away from the chassis to separate it from the boot.
14
Step 14
- Use your hand to completely pull the ring off the boot.
- Insert one end of the ring into its groove along the boot's perimeter.
- Use pliers to slowly stretch the ring around the boot's perimeter until it's completely nested in its groove.
15
Disconnect the boot
- Use your fingers to pull the boot off its lip on the front panel.
16
Step 16
- Slide your fingers around the lip of the boot until it's completely separated from the panel.
17
Remove the filter panel
- Open the filter panel at the bottom of the front panel.
- Unclip the filter panel.
18
Drain the machine
- Place a bowl next to the machine.
- Pull the drain filter hose out of its slot in the chassis enough to lay over the bowl.
- Remove the plug at the end of the drain filter hose to release excess water into the bowl.
19
Unfasten the filter trim
- Remove the screw(s) securing the filter trim.
20
Remove the filter trim
- Pull the filter trim straight off the front panel to remove it.
21
Unfasten the lower front panel
- Remove the screw(s) securing the lower front panel.
22
Unfasten the door latch
- Remove the screw(s) securing the door latch.
23
Remove the door latch
- Pull the door latch through its slot in the chassis and let it hang on its wire.
24
Unfasten the front panel
- Remove the screw(s) securing the front panel.
25
Remove the front panel
- Lift the front panel upward to separate it from its clips on the bottom of the chassis.
- Pull the front panel away from the chassis to completely separate the front panel.
26
Step 26
- Remove the front panel.
27
Unfasten the rear panel
- Remove the screw(s) securing the rear panel.
28
Remove the rear panel
- Unclip the rear panel from the chassis.
29
Step 29
- Remove the rear panel.
30
Disconnect the drain hose
- Use slip joint pliers to pinch the drain hose clamp and slide it up the hose away from the pump assembly.
31
Step 31
- Use slip joint pliers to rotate the drain hose back and forth around its connection and loosen it.
- Pull the drain hose straight off its connection on the assembly.
32
Unclip the drain hose
- While holding the back of clip with one hand, use the other to push the prongs of the clip and release them.
- Repeat for each prong until the clip slides through the chassis.
33
Reposition the drain hose
- Reposition the drain hose so you can access the plastic clip.
34
Unfasten the drain hose
- Remove the screw(s) securing the drain hose.
35
Apply the tape
- To prevent confusion during reassembly, apply some masking tape where the plastic clip is located.
36
Remove the plastic clip
- Pull the plastic clip off the drain hose.
- Remove the plastic clip.
37
Remove the drain hose
- Pull the drain hose through its slot in the chassis.
38
Step 38
- Remove the drain hose.
To reassemble your device, follow these instructions in reverse order.
Take your e-waste to an R2 or e-Stewards certified recycler.
Repair didn’t go as planned? Ask our Answers community for help.
«LG Front Load Washing Machine Drain Hose Replacement» — автор Bill Gilbert, iFixit, лицензия CC BY-NC-SA 3.0. Показано без изменений. Открыть оригинал и комментарии →